S1050 LED FLASHLIGHT
User Manual
TROUBLESHOOTING
If the flashlight flickers, works intermittently, changes modes automatically, appears
dim or faded, or does not turn on, check and verify that:
• Each battery is fully inserted matching the polarity (+/-) on the battery holder.
• Each battery end is touching a metal contact in the battery holder.
• The battery holder contacts are clean and the springs are not bent sideways.
• The flashlight's inner spring is firmly attached and not bent.
• The battery holder is inserted into the flashlight with the positive (+) end first.
• The tail cap is twisted on tightly.
Firmly press the power button on and o several times:
• If the flashlight still does not turn on, replace the batteries.
• If the problem persists, contact GearLight for a replacement.
Irvine, California | USA | www.GearLight.com
WARRANTY AND LIMITATION OF LIABILITY
MAINTENANCE
Inspect the flashlight monthly and carefully remove any damaged batteries and clean
any corrosion. If the flashlight is used less than once a month, remove the
batteries between uses. Lubricate all threads and
rubber O-rings with petroleum
jelly twice yearly.
Limited One-Year Warranty
GearLight warrants this product for one year from the date of purchase
against any defects in material or workmanship. This warranty does not cover
normal wear and tear, nor damage resulting from misuse or neglect. We will,
at our discretion, repair, replace, or refund the purchase price of this product
should we determine it to be defective.
Limitation Of Liability
Liability limited to the purchase price of this product. GearLight shall not be
liable for any incidental or consequential damages or any implied warranty on
this product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion
may not apply to you.
FOR YOUR SAFETY, READ BEFORE OPERATING
v2
2x GearLight S1050 LED Flashlights
2x 18650 Battery Tubes (Batteries Are Not Included)
2x AAA Battery Holders (Inside Flashlights)
2x Lanyards
1x User Manual
1x Warranty Card
Package Contents:
IMPORTANT SAFETY NOTICE: Lithium-ion batteries are potentially hazardous and can
present a fire, explosion, and burn hazard. By using lithium-ion batteries, you agree that
GearLight shall not be liable for any incidental or consequential damages arising from,
relating to or connected with the use of lithium-ion batteries. If you do not agree with
these conditions, please use only alkaline or NiMH rechargeable batteries.
WARNING: To avoid eye injury, do not stare directly into the light beam or shine
the beam directly into anyone’s eyes. This product is not designed, intended, or
recommended for children or hazardous environments.
CAUTION: The flashlight may become warm or hot after extended periods of use
at the highest setting. Select a lower setting when the flashlight is hot. This is
typical for high-powered flashlights and does not cause damage to the flashlight.
AAA Battery Installation (See Warning)
1. Unfasten tail cap and remove battery holder.
2. Insert three (3) AAA batteries following
the correct polarity (+,-) marked on the
battery holder.
3. Insert the battery holder into the
flashlight with the positive (+) end first.
On/O
• To turn the flashlight on, press down firmly on the red power button located on
the tail of the flashlight until you hear a click.
• To turn the flashlight o, press down firmly again until you hear a click.
Twist Zoom
1. Hold both ends of the flashlight; gently twist clockwise to extend and focus.
2. Twist the opposite direction for a broad dispersed light beam.
Switching Modes
• There are 3 dierent lighting modes: HIGH, MEDIUM, LOW
• To switch through the 3 dierent lighting modes, gently press down on the
red power button.
• The flashlight will switch to the next mode when turned o and on in quick
succession. It will reset to high mode after being o for more than 10 seconds.
GETTING STARTED
OPERATIONS
WARNING: Always follow the battery manufacturer’s instructions as to the proper
usage, handling, storage, and disposal of batteries. Use only batteries from a
reputable manufacturer. Do not mix dierent brands or types of batteries in the
same flashlight. Replace all batteries at the same time. Failure to follow safety
instructions may result in personal injury and damage to property.
POWERFUL
LED
LANYARD
TWIST ZOOM
DESIGN
ANTISLIP
BODY
RUBBER
O-RING
TAIL
CAP
POWER
BUTTON
AAA BATTERY
HOLDER
NEGATIVE POSITIVE
+ –
NEGATIVE POSITIVE
+ –
WARNING: Lithium-ion batteries can present a fire, explosion, and burn hazard. Use
only 18650 battery cells with a protection circuit produced by Panasonic, Sanyo,
Sony, Samsung, or LG. Remove the battery when the flashlight is not in use. The use
of other cell manufacturers or the failure to follow the battery manufacturer's safety
instructions may result in fire, explosion, personal injury, and damage to property.
18650 3.7v Lithium-ion Rechargeable Battery Installation (See Warning)
1. Insert one 18650 battery (Fig. 1) inside the 18650 clear battery tube (Fig. 2).
2. Insert the combined 18650 battery and clear tube into the flashlight with the
positive (+) end first.
Fig. 1
Fig. 2
+
18650
RECHARGEABLE
LITHIUM-ION BATTERY
-
HIGH
MEDIUM
LOW